By Luis Lopez, AI transportation consultant, CEO of Go Hub.io Holdings Corp and subsidiaries, and host of the Freight Guru Podcast
A curtainside trailer sits somewhere between a dry van and a flatbed. It has a roof, a rigid front, rear doors and a floor like a van, but its sides are heavy fabric curtains that slide open along a track. Pull the curtain back and the whole side of the trailer is open for a forklift. Close it and the freight is covered.
That design solves a specific problem: freight that needs side access for loading or unloading but should not ride fully exposed. This article explains how a curtainside trailer works, where it fits, how it compares with other equipment, and what to confirm when you book one.
How a Curtainside Trailer Works
The basic parts are straightforward:
- Roof and frame. A fixed or sliding roof supported by the front bulkhead, the rear frame and removable or sliding posts along the sides.
- Curtains. Reinforced fabric panels that hang from a rail at the top and slide toward the front or rear. Tensioning devices pull them tight when closed.
- Posts. Side posts support the roof. Many designs let the posts slide or lift out so a forklift has a wider opening.
- Rear doors. Most units also load from the back, like a van.
- Deck. A flat floor with rails or anchor points for straps and other securement devices.
Because the trailer can load from the sides and the rear, a single unit can take freight at a dock and then deliver to a site with no dock at all.
Side Loading and Rear Loading
Side loading is the main reason to choose curtainside equipment. A forklift can drive up beside the trailer, place a pallet anywhere along the deck, and back away. That matters when the receiver has no loading dock, when freight is long or awkward to push down the length of a van, or when stops need to be unloaded in a particular order.
Rear loading still works at a standard dock. Some shippers load from the back at their facility and the receiver unloads from the side at a job site or yard. That flexibility is useful for multi-stop routes where each customer has different facilities.
Where Curtainside Fits
As an AI transportation consultant, the first thing I look at when someone asks about curtainside equipment is the delivery end. If the receiver has a dock and the freight is palletized, a dry van is usually simpler. If the receiver has no dock and the freight can handle weather exposure, a flatbed may be enough. Curtainside earns its place in between.
Common fits include:
- Building materials. Bagged products, boxed fixtures, insulation, drywall and other materials that should stay dry but arrive at sites with no dock.
- Palletized goods to non-dock locations. Retail store back lots, rural distributors and yards where a forklift is available but a dock is not. For other ways to handle these deliveries, see our guide to non-dock delivery and liftgates.
- Mixed loads. Multi-stop runs where a driver needs to pull one customer’s pallets out of the middle of the trailer without unloading everything in front of them.
- Long or bulky items. Products that are hard to maneuver through rear doors but still need cover.
Curtainside Versus Other Equipment
Dry Van
A dry van has rigid walls and loads only from the rear. It offers stronger weather protection and better security against theft, and it is far easier to find in the US market. Its weakness is access: freight has to go in and out through the back, which usually means a dock or a liftgate. Our article on swing door vs roll-up door trailers covers another van detail that affects loading.
Flatbed
A flatbed loads from any side and from above, including by crane. It handles heavy, tall and oversized freight that no enclosed trailer can take. The trade-off is exposure. Freight that cannot get wet needs tarps, and tarping takes time, labor and agreement on who provides the tarps. For the full picture, see flatbed freight explained.
Rolling Tarp Systems
Flatbeds fitted with a sliding tarp frame offer a similar idea: covered freight with open access. They usually allow overhead loading when the cover is pulled back, which curtainside units with a fixed roof may not. The right choice depends on whether the shipper needs crane access, how much the freight weighs, and what is available on the lane.
The Curtain Is Not Securement
This is the point that causes the most trouble. A closed curtain looks like a wall, but it is weather protection, not a cargo restraint. Freight inside a curtainside trailer must still be secured under the federal cargo securement rules at 49 CFR 393.100 through 393.136, which include general rules for all cargo and commodity-specific sections for certain products.
In practice that means:
- Pallets and bundles are strapped, blocked or otherwise restrained to the deck, just as they would be on a flatbed.
- Freight is not allowed to lean against the curtain. A shifting load can bulge, tear or burst a curtain, and anything that falls through it is a hazard on the road.
- The front bulkhead does its job only if the load is positioned and restrained so it cannot slide forward with force.
Shippers sometimes assume a curtainside load can be treated like a van load. It cannot. The driver needs anchor points, straps and time to secure each stop’s freight after loading.
Availability in the US
Curtainside trailers are common in several other freight markets, where side loading is a standard part of regional distribution. In the US they are a niche piece of equipment by comparison. Dry vans and flatbeds dominate most lanes, and the curtainside units that do run tend to be concentrated in certain regions, private fleets and specialized carriers.
That has practical consequences. You may not find a curtainside truck on short notice, rates can reflect the limited supply, and some carriers will offer a flatbed with tarps or a rolling tarp unit instead. Build lead time into the plan.
Booking Tips
When you request curtainside equipment, give the carrier enough detail to say yes with confidence:
- Describe the freight. Commodity, pallet count, dimensions, weight and whether anything is fragile or stackable.
- Explain the loading method at each end. Dock, side forklift, or both. Note whether posts need to be moved for wide pallets.
- List the stops in order. Mixed loads should be planned so each stop’s freight can be reached from the side.
- Confirm securement expectations. Who supplies straps, edge protection and blocking, and whether the driver is expected to help load.
- Ask about substitutes. If no curtainside unit is available, decide in advance whether a tarped flatbed or a rolling tarp trailer is acceptable.
- Document condition. Note any exceptions on the bill of lading at pickup and at delivery, and take photos of the secured load.
The Bottom Line
A curtainside trailer is a practical tool for covered freight that needs side access, especially for building materials and palletized deliveries to sites without docks. It is not a substitute for proper securement, and it is not always easy to find. Match the equipment to the delivery site, plan the securement as if the curtain were not there, and have a backup option ready.
For more conversations on freight and AI, subscribe to the Freight Guru Podcast.
About the author: Luis Lopez is a Miami-based AI transportation consultant and logistics entrepreneur, the CEO of Go Hub.io Holdings Corp and subsidiaries, and host of the Freight Guru Podcast.


